Main Menu
Please::Support::Our Sponsors
Device Forums
MGN News Feed
|
|
|
How to fix your MPx200 when it will not charge.... |
|
|
|
|
Gadget Junkie
Group: Members
Posts: 114
Joined:
From: Chicago Suburbs, IL
Member No.: 2,780
|
DISCLAIMER: You do this at your own risk! There are very small parts on the circuit board and many of them are probably static sensitive. You WILL void your warrantee by doing this and I take NO responsibility for any of the procedures or information that I am providing below. This procedure fixed my phone, yours may be a different problem so you are on your own. Sorry I have to state all this, but you should understand that if you ruin your phone, it is not my fault. Also, if you have never soldered before – I would highly recommend you find someone to do this for you. Again these are very small parts, so you need a very fine tipped soldering iron with a low heat setting. No 100W soldering guns allowed ;-) I would also recommend you wear a static strap that is grounded and you work on a very clean hard surface. With all that stated – Good luck! Tools needed: Torx T5 dirver Digital Multi-meter Very fine tipped soldering iron settable to low heat Acid free solder, very thin – NOT PLUMBING SOLDER Solder wick 0603 size replacement fuse, 0 Ohm resistor, small piece of wire, blob of solder – something to repair the fuse. Obviously the best thing to do is to use a replacement fuse. The designer of the phone thought it was needed, but you do what you want. You can find suppliers of 0603 surface mount fuses on the web, such as http://www.schurterinc.com . The fuse that was used is marked with an F, which signifies a 0.5A rating. If you want to go up a size or two, G is a 0.75A and H is a 1.0A. Surface mount fuses are notorious for de-rating after time, reflow soldering, etc. So very likely 0.5A is the correct size to use, but just after time or the manufacturing process the fuse just blew at a lower current level. Take your phone apart according to the directions in the "How to strip your MPx200" sticky. You only need to remove the main PCB under the battery compartment. Once you have done this flip the PCB over and look towards the top and locate the fuse, see the attached picture. It is ironically marked with an "F". With your multimeter check the continuity over this component, if it is open then your fuse is blown. If you have continuity over this part, then you have a different problem with your phone. I would start by checking the solder joints on the USB connector. First, remove the old fuse. This is easier if you have two soldering irons. Then remove any excess solder from the pads with the solder wick. Then carefully solder the new fuse in it's place. There are other traces and components near by, so use as little solder as possible and be very carefull not to short anything else out. That is it, put the phone back together and see if it works. This has worked on two phones, so 2 out of 2 isn't too bad. ;-)
Attached File(s)
fuse.jpg ( 132.5K )
Number of downloads: 126
|
|
|
|
|
|
Advanced Member
Group: Members
Posts: 97
Joined:
Member No.: 2,476
|
Firstly, how did you come across this? Do you have any knowledge as to why this affects the charging of the battery to full capacity? What does doing a hard reset have to do with this fuse? The procedure you gave is very detailed and easy to follow. I just like to know the why's before I crack open cases on cell phones.
|
|
|
|
|
|
Gadget Junkie
Group: Members
Posts: 114
Joined:
From: Chicago Suburbs, IL
Member No.: 2,780
|
I came across this as my phone stopped charging the battery. I tried the hard reset bit with no success. I then spoke with some other members and they also had this same problem. I have a technical background, so I figured it should not be too hard to figure out why a battery will not charge. So I took my phone apart, plugged in the charger and started probing every pin on the board for voltage. I came across this part, the big "F" on it grabbed my attention anyways, and found 5 volts on one side and 0 volts on the other - BINGO. Then started looking into what this component was and found that the F marking stands for a 0.5A fuse. So when this fuse blows, the 5 volts from the USB port is disconnected from the phone - basically it is like it is not even plugged in.
In thinking about this further, the 0.5A rating makes sense as USB ports are rated at a maximum of 0.5A. If you exceed this ammont most computers will shut that USB port down. This fuse probably protects the computer as well as the phone.
From what I have gathered there are two possible causes for the phone not charging, one being a software glitch fixable by a hard reset and the other being a true hardware fault - this fuse.
|
|
|
|
|
|
Advanced Member
Group: Members
Posts: 97
Joined:
Member No.: 2,476
|
Was your fault that it completely would not charge, or that it had poor battery life? I am experiencing poor battery life, and in rereading your post, I doubt this is my problem.
|
|
|
|
|
|
Gadget Junkie
Group: Members
Posts: 114
Joined:
From: Chicago Suburbs, IL
Member No.: 2,780
|
It would not charge at all - no indication on the phone that it was even plugged in.
I have heard that if you hard reset with a partially dead battery that the phone records that battery voltage as the "full" level - so it will not charge past that point. I do not know if this is true, but the problem I see is that if this is true - how do you get a fully charged battery to reset it to the right level then?
|
|
|
|
|
|
Advanced Member
Group: Members
Posts: 97
Joined:
Member No.: 2,476
|
The only way that I can think of would be to charge the battery with an external charger, AKA another MPx200 that works. I haven't tried that yet because I don't have any friends with an MPx200. Do any other motorola's use the same battery? Probably not, knowing Moto.
|
|
|
|
|
|
Gadget Junkie
Group: Members
Posts: 114
Joined:
From: Chicago Suburbs, IL
Member No.: 2,780
|
In reading this post it seems that if you turn the phone off and let it completely charge until it vibrates indicating that it is done, it will fully charge. Then reflash the phone and it "should" recharge normally to that level. I am not sure of all this, just passing on what I've read.
|
|
|
|
|
|
Gadget Junkie
Group: Members
Posts: 114
Joined:
From: Chicago Suburbs, IL
Member No.: 2,780
|
Just for my own gratification I would love to hear if this information helped you fix your phone. I am curious if there are other hardware faults besides this fuse that is causing the same type of failure. So please post here if this has helped or not.
Thanks
|
|
|
|
|
|
Gadget Junkie
Group: Members
Posts: 113
Joined:
Member No.: 1,161
|
If you're having problems charging your phone, before taking apart your phone, I would first suggest you go into engineering mode by dialing * #**364# and pressing the middle blue key, and then going to Options > Layer 1B > Force Charge. Also, I would suggest sending your phone back to Motorola under warranty rather than taking it apart, as that would void your warranty.
|
|
|
|
|
|
Newbie
Group: Members
Posts: 4
Joined:
Member No.: 5,802
|
Force Charge. I saw that in the Eng mode as well. Do you know for sure that this resets the phone to see the battery as fully charged or are you just guessing because it has the words 'force' and 'charge' in it?
-c
|
|
|
|
|
|
Newbie
Group: Members
Posts: 1
Joined:
Member No.: 7,239
|
QUOTE (huckfinn @ Nov 30 2004, 01:16 PM) I came across this as my phone stopped charging the battery. I tried the hard reset bit with no success. hi huckfin tell me how to hard reset my mpx200 i want to do this fist before open my phone its brand new but the ebay seller no see again have waranty but no answers regards (IMG: http://www.mobilegadgetnews.com/style_emoticons/default/biggrin.gif)
|
|
|
|
|
|
Newbie
Group: Members
Posts: 1
Joined:
Member No.: 7,261
|
Hey, I was reading this post and decided to create an account just to say this worked for me! My phone was acting funny (sim not detected, then not booting) and finally it just *died*. I couldnt charge it, and even when plugged in, nothing would show up. I took the plunge to try to *fix* it and it works! Although I didnt replace the fuse, I just bridged the connections across the fuse. Hopefully this wont melt my phone, or at least until I can get a good deal on a newer gen. phone (IMG: http://www.mobilegadgetnews.com/style_emoticons/default/biggrin.gif) . Thx for everything!
|
|
|
|
|
|
Gadget Junkie
Group: Members
Posts: 114
Joined:
From: Chicago Suburbs, IL
Member No.: 2,780
|
QUOTE (Mr DDD @ Feb 9 2005, 07:31 AM) hi huckfin tell me how to hard reset my mpx200 i want to do this fist before open my phone its brand new but the ebay seller no see again have waranty but no answers regards (IMG: http://www.mobilegadgetnews.com/style_emoticons/default/biggrin.gif) Hold the blue button while you turn the phone on and then answer YES when it asks you. Be sure your battery is fully charged and be patient, the hard reset can take a few minutes to complete.
|
|
|
|
|
|
Newbie
Group: Members
Posts: 1
Joined:
Member No.: 7,514
|
wow. thank you very much. worked like a charm.
Due to lack of tools and expertise, instead of replacing the fuse, I shorted it out, too. However my main charging device is my laptop. So there should be a fairly stable voltage coming out ot my USB port. Therefore the fuse may not be a vital component for me.
This post has been edited by othello:
|
|
|
|
|
|
Gadget Junkie
Group: Members
Posts: 128
Joined:
From: USA
Member No.: 5,641
|
i want to know what is the name of that fuse that i need to buy to repair my phone i went to that website what u gave in post before but i dont know witch fuse i should pick so please tell me the name of that fuse in this website
|
|
|
|
|
|
Super Moderator
Group: Members
Posts: 206
Joined:
From: Washington DC
Member No.: 593
|
QUOTE (Seba641 @ Apr 2 2005, 06:47 PM) i want to know what is the name of that fuse that i need to buy to repair my phone i went to that website what u gave in post before but i dont know witch fuse i should pick so please tell me the name of that fuse in this website Did you get a reply which fuse to buy?
|
|
|
|
|
|
Gadget Junkie
Group: Members
Posts: 114
Joined:
From: Chicago Suburbs, IL
Member No.: 2,780
|
If you get the fuse from Schurter it is the following...
3412.0113.24 for the 0.5 A fuse (stock size) 3412.0114.24 for the 0.75 A fuse 3412.0115.24 for the 1.0 A fuse
|
|
|
|
|
|
Newbie
Group: Members
Posts: 1
Joined:
Member No.: 8,533
|
for those who use only standart charger and usb cable to charge the phone. it is not necessary to change the broken fuse with another one. More easier is just to short the broken fuse and the other step is to insert any other 0.4-0.5 fuse in the charger. Also if your mpx charges with no problems now it will be good if you insert 0.4-0.5 fuse in your charger. may be it will protect your phones fuse in future. So why i writing all this. i just can't find 0.4-0.5 fuse. if i'll do parallel connection between two 0.25 fuses will it work like one 0.5 ???? sorry for my bad english, but i guess the main idea of the post is quite clear (IMG: http://www.mobilegadgetnews.com/style_emoticons/default/smile.gif) huckfinn thx for useful solution
|
|
|
|
|
|
Member
Group: Members
Posts: 24
Joined:
Member No.: 8,055
|
well i have 3 mpx 200's and 1 died a long time ago, because i pluged in the charger wile doing a hr... (IMG: http://www.mobilegadgetnews.com/style_emoticons/default/unsure.gif) so i didint change the fuse i just bridged it to see and it will still not turn on and i know its that part of the phone because i put one from one of the others and it turns on what else can it be???
|
|
|
|
|
|
Newbie
Group: Members
Posts: 7
Joined:
Member No.: 5,733
|
QUOTE (madmaxedcn @ May 9 2005, 05:28 AM) well i have 3 mpx 200's and 1 died a long time ago, because i pluged in the charger wile doing a hr... (IMG: http://www.mobilegadgetnews.com/style_emoticons/default/unsure.gif) so i didint change the fuse i just bridged it to see and it will still not turn on and i know its that part of the phone because i put one from one of the others and it turns on what else can it be??? My MPx200 stopped charging a couple days ago. I took the phone apart according to the guide and repair instructions. I decided to take the risk and bridge the fuse instead. My MPx lives again!! This phone is starting to remind me of my 1st "do it yourself " pc... An Emachine! Thanks to: Awarner, Huckfinn and Neeki.
|
|
|
|
|
|
Newbie
Group: Members
Posts: 2
Joined:
Member No.: 8,717
|
QUOTE (huckfinn @ Nov 29 2004, 01:51 PM) DISCLAIMER: You do this at your own risk! There are very small parts on the circuit board and many of them are probably static sensitive. You WILL void your warrantee by doing this and I take NO responsibility for any of the procedures or information that I am providing below. This procedure fixed my phone, yours may be a different problem so you are on your own. Sorry I have to state all this, but you should understand that if you ruin your phone, it is not my fault. Also, if you have never soldered before – I would highly recommend you find someone to do this for you. Again these are very small parts, so you need a very fine tipped soldering iron with a low heat setting. No 100W soldering guns allowed ;-) I would also recommend you wear a static strap that is grounded and you work on a very clean hard surface. With all that stated – Good luck! Tools needed: Torx T5 dirver Digital Multi-meter Very fine tipped soldering iron settable to low heat Acid free solder, very thin – NOT PLUMBING SOLDER Solder wick 0603 size replacement fuse, 0 Ohm resistor, small piece of wire, blob of solder – something to repair the fuse. Obviously the best thing to do is to use a replacement fuse. The designer of the phone thought it was needed, but you do what you want. You can find suppliers of 0603 surface mount fuses on the web, such as http://www.schurterinc.com . The fuse that was used is marked with an F, which signifies a 0.5A rating. If you want to go up a size or two, G is a 0.75A and H is a 1.0A. Surface mount fuses are notorious for de-rating after time, reflow soldering, etc. So very likely 0.5A is the correct size to use, but just after time or the manufacturing process the fuse just blew at a lower current level. Take your phone apart according to the directions in the "How to strip your MPx200" sticky. You only need to remove the main PCB under the battery compartment. Once you have done this flip the PCB over and look towards the top and locate the fuse, see the attached picture. It is ironically marked with an "F". With your multimeter check the continuity over this component, if it is open then your fuse is blown. If you have continuity over this part, then you have a different problem with your phone. I would start by checking the solder joints on the USB connector. First, remove the old fuse. This is easier if you have two soldering irons. Then remove any excess solder from the pads with the solder wick. Then carefully solder the new fuse in it's place. There are other traces and components near by, so use as little solder as possible and be very carefull not to short anything else out. That is it, put the phone back together and see if it works. This has worked on two phones, so 2 out of 2 isn't too bad. ;-) [COLOR=blue][FONT=Arial]
|
|
|
|
|
|
Newbie
Group: Members
Posts: 2
Joined:
Member No.: 8,717
|
Guys you are the best thing after soap and water!!! My knowledge is limited on this electronics stuff and thanks to Huck and friends I fix my phone (for now). My MPX200 stop charging and after reading your posting I tried to buy and/or order the fuse without luck, then decided buy the $3 Torx5 screwdriver and open the phone. It was the only shot I got (Motorola won't fix it). I followed the instructions to the dots and bridged the fuse (very careful) and PUFF!!! The phone is alive again!!! I'll keep it until I get a good deal on a MPX220. You guys have no idea how thankful I am to you for your posting. Keep up the wonderful work! Thanks Luis FT Bragg, NC
|
|
|
|
|
|
Newbie
Group: Members
Posts: 1
Joined:
Member No.: 8,722
|
I came across this page on the Internet and I just found the solution to my MPX200 problem. I would like to thank you so much "huckfinn". Actually, I just registered in this forum just to thank you for sharing your knowledge with everyone. Your post is wonderful, and your information is so much appreciated, you just don't know. Good luck. Salam
This post has been edited by knight_2004:
|
|
|
|
|
|
Newbie
Group: Members
Posts: 1
Joined:
Member No.: 4,901
|
can i remove the chip,and just connect the 2 connection straigh foward with solder
|
|
|
|
|
|
Gadget Junkie
Group: Members
Posts: 114
Joined:
From: Chicago Suburbs, IL
Member No.: 2,780
|
QUOTE (prodigio2k @ May 17 2005, 01:49 PM) can i remove the chip,and just connect the 2 connection straigh foward with solder That is the same as bridging over the fuse, so yes you can. I recommend finding a replacement fuse, but this works as well - just be sure to use a fused charger then. Same disclaimers apply as I put in the original post (IMG: http://www.mobilegadgetnews.com/style_emoticons/default/wink.gif) . On a side note, thanks for all of the kind words. It is nice to hear that the information I provided is being used and appreciated. I have finally replaced my MPx200 with a MPx220, so I do not always browse this forum. I repaired my phone back in November of last year and it is still working, just wanted a new one (IMG: http://www.mobilegadgetnews.com/style_emoticons/default/rolleyes.gif) . If you need any additional guidance/help, fire me off a personal message and I will see what I can do.
|
|
|
|
|
|
Member
Group: Members
Posts: 26
Joined:
Member No.: 9,481
|
QUOTE (huckfinn @ Nov 29 2004, 01:51 PM) DISCLAIMER: You do this This has worked on two phones, so 2 out of 2 isn't too bad. ;-) Huck you the bomb! Im one of the many writing to say thanks for bringing my MPx200 back from what was going to be a sure death. A power surge burned the fuse out and I would have never found it with out you, Thanks again. I signed on for the first time to thank you and add one tip for the fuse blowers out there that are concerned about jumping the fuse with no protection and having a hard time finding an exact fuse replacement. I think you can get .5A of protection if you get an old style .5A auto fuse ( the clear glass tube with metal capped ends) ,break the glass and take the fine metal fuse wire out. Solder the fuse wire, cut to fit to each end of the installed surface mounted fuse. Im not an electrician and I no cars run on 12 volts but I think the .5A fuse wire still gives you the protection. Good luck to all its a tight fit and I had to grind my soldering gun tip down to a pin point, but the good news is Im 1 for 1.
This post has been edited by Pigpaw3:
|
|
|
|
|
|
Newbie
Group: Members
Posts: 1
Joined:
Member No.: 9,647
|
QUOTE (huckfinn @ Nov 29 2004, 05:51 PM) DISCLAIMER: You do this at your own risk! There are very small parts on the circuit board and many of them are probably static sensitive. You WILL void your warrantee by doing this and I take NO responsibility for any of the procedures or information that I am providing below. This procedure fixed my phone, yours may be a different problem so you are on your own. Sorry I have to state all this, but you should understand that if you ruin your phone, it is not my fault. Also, if you have never soldered before – I would highly recommend you find someone to do this for you. Again these are very small parts, so you need a very fine tipped soldering iron with a low heat setting. No 100W soldering guns allowed ;-) I would also recommend you wear a static strap that is grounded and you work on a very clean hard surface. With all that stated – Good luck! Tools needed: Torx T5 dirver Digital Multi-meter Very fine tipped soldering iron settable to low heat Acid free solder, very thin – NOT PLUMBING SOLDER Solder wick 0603 size replacement fuse, 0 Ohm resistor, small piece of wire, blob of solder – something to repair the fuse. Obviously the best thing to do is to use a replacement fuse. The designer of the phone thought it was needed, but you do what you want. You can find suppliers of 0603 surface mount fuses on the web, such as http://www.schurterinc.com . The fuse that was used is marked with an F, which signifies a 0.5A rating. If you want to go up a size or two, G is a 0.75A and H is a 1.0A. Surface mount fuses are notorious for de-rating after time, reflow soldering, etc. So very likely 0.5A is the correct size to use, but just after time or the manufacturing process the fuse just blew at a lower current level. Take your phone apart according to the directions in the "How to strip your MPx200" sticky. You only need to remove the main PCB under the battery compartment. Once you have done this flip the PCB over and look towards the top and locate the fuse, see the attached picture. It is ironically marked with an "F". With your multimeter check the continuity over this component, if it is open then your fuse is blown. If you have continuity over this part, then you have a different problem with your phone. I would start by checking the solder joints on the USB connector. First, remove the old fuse. This is easier if you have two soldering irons. Then remove any excess solder from the pads with the solder wick. Then carefully solder the new fuse in it's place. There are other traces and components near by, so use as little solder as possible and be very carefull not to short anything else out. That is it, put the phone back together and see if it works. This has worked on two phones, so 2 out of 2 isn't too bad. ;-) thank you for the tip, it charge again.
|
|
|
|
|
|
Newbie
Group: Members
Posts: 1
Joined:
Member No.: 9,949
|
Thank I resolved my problem with using what you write. I had some problem to soldering but now my Mpx200 is working :D
|
|
|
|
|
|
Newbie
Group: Members
Posts: 2
Joined:
Member No.: 8,674
|
I am experiencing this very problem. I just purchased the fuse listed previously in this post from Shurter.com and plan to follow the steps to see what happens. Sounds like this is working for some people. The minimum order from Shurter however was 10 fuses, so of course I ordered 10. I only plan on using one and keeping a couple as backups so if anyone needs one feel free to email me at sthompson@bfmed.net and I can drop one in the mail for you. They were cheap, lik 48 cents a piece. I haven't tried a hard reset because you need a fully charged battery when doing this and since I have no way to charge my phone, I can't get a full battery. Thanks to everyone for the good info! If this doesn't work I'm going with the Moto A1000! But I love my MPX200! All my friends are blown away when I pull it out to listen to music! Anyone have the Shure ear buds? Completely blocks out all ambient noise leaving you with peace and quite and great sounding music. Great for air travel. Check em out if you like! http://www.shurestore.com/earphones/eseries_e2c.htmleBay has them too, or course. Serious bragging rights having a device that replaces an iPod and makes calls! Let alone all the other features (ie Flight Mode, Sync, Calendar, Contacts...) the phone offers, as yo uall know I'm sure. (IMG: http://www.mobilegadgetnews.com/style_emoticons/default/biggrin.gif) I have about 2 hours of battery life left. And after that I can only hope and pray my phone will come back to life once I replace the fuse. I'll let you know how it goes.
|
|
|
|
|
|
Newbie
Group: Members
Posts: 2
Joined:
Member No.: 8,674
|
Unsuccessful. Rats! Be sure your soldering iron is very thin iron!
|
|
|
|
|
|
Newbie
Group: Members
Posts: 6
Joined:
Member No.: 8,348
|
I am going to do this on my phone in few days. I am collecting all necessary tools right now. BTW I would like to know whether 30W soldering iron is more than what I needed or just perfect. Will let you know guys how did this work out for me. Thanks for the great tips and advice.
|
|
|
|
|
|
Newbie
Group: Members
Posts: 1
Joined:
Member No.: 10,307
|
Just another experience. Same problem - By the way, I think my problem happened when I plugged in the phone in the US (don't worry - the charger is rated for 50-60Hz, 100-240v). But since then, the phone worked OK but wouldn't charge. Followed the procedure and all OK for a few weeks. Unfortunately, I now have a new problem that the phone seems to have shorted out. I have pretty much a short across the 5V. Went back in and cut my link (didn't bother with a fuse in the original repair !! (IMG: http://www.mobilegadgetnews.com/style_emoticons/default/ohmy.gif) ) and now the short is removed but the phone is not charging. When I bridge the fuse again, I have a short again - I wanted to make sure that some of my fine soldering work hadn't bridged something else. So, it looks like the fuse blew originally because of some intermittant short condition. So, my recommendation is that you replace the fuse with a fuse, or better still put a fuse in-line somewhere else. By the way, I noticed something else that could be either a cause or a result of the problem. On the picture included already in this topic, the slightly larger component above the fuse (marked with E 2 ) now appears to have blown. There is a dimple on the component package and heat marks. Don't suppose anyone knows what this is ? I think my investigation work stops here and MPX RIP! Thanks for the original suggestion anyway. Colum
|
|
|
|
|
|
Newbie
Group: Members
Posts: 2
Joined:
Member No.: 10,588
|
QUOTE (Toad @ Dec 2 2004, 11:16 AM) If you're having problems charging your phone, before taking apart your phone, I would first suggest you go into engineering mode by dialing * #**364# and pressing the middle blue key, and then going to Options > Layer 1B > Force Charge. Also, I would suggest sending your phone back to Motorola under warranty rather than taking it apart, as that would void your warranty. Force charge works a treat m8. As Toad says and thanks to him for the tip. I picked up a mpx200 on ebay uk sim locked to orange. The first thing I done of course was to flash upgrade the phone to win mobile 2003 to unlock it and get rid of all the orange stuff on it. But to my dismay the charge the battery held was awfull (IMG: http://www.mobilegadgetnews.com/style_emoticons/default/sad.gif) (probably because I didnt make sure the phone was fully charged before I done the upgrade). So I tried the force charge thing that Toad suggested and also done a full reset (switch phone on while pressing the blue button) And volia! its now 30 hours since I done it and the battery i still at 90% charge! . Not a bad improvement from 4 hours max! One word of warning. A full reset will clear all your personal settings to default. Things like your calendar entries, phone owner info, Internet settings will go back to default. THe only thing I am now having problems with is getting the o2 GPRS internet working (IMG: http://www.mobilegadgetnews.com/style_emoticons/default/sad.gif) anyone ?
|
|
|
|
|
|
Newbie
Group: Members
Posts: 1
Joined:
Member No.: 10,698
|
Anyone who bridged the connection between the fuse? So far any problems with the charging and the phone?
I fused the charger and hopefully it will avoid blowing any fuses in the phone in the future. =)
This post has been edited by rsys6868:
|
|
|
|
|
|
Newbie
Group: Members
Posts: 3
Joined:
Member No.: 10,720
|
Thanks ... phone works great. I bridged the fuse after giving up on trying to get it off... when I get back home (currently at college) I'll have access to another soldering iron, which will help a lot. I just ordered the fuses from Schurter... msyd34 lost 'em. They were $.48 a piece, had to order ten, just like he said... though their shipping prices are currently in low orbit ($10 (IMG: http://www.mobilegadgetnews.com/style_emoticons/default/blink.gif) ). If any of you guys need one, shoot me an email (just look in my profile for the link, it'll get to me). Hopefully mine won't disappear into the black hole of doom junk drawer too, but I can't make any guarantees (IMG: http://www.mobilegadgetnews.com/style_emoticons/default/unsure.gif) As for your question rsys6868, I soldered a little wire over the fuse. It seemed like it was on there somewhat weakly, but I've managed to drop the phone on to carpet once or twice and left it on vibrate through a salvo of text messages... still works great. Keep in mind, though, this is a less than ideal permanent solution... the fuse gave its life for some reason or another, so there's a very real chance your phone could be next w/o the fuse. And I was wondering, how long did you guys have your MPx's before you had to do this? Mine's been alive and kicking for about two and a half years now... and still going strong.
|
|
|
|
|
|
Senior Member
Group: Members
Posts: 66
Joined:
Member No.: 7,964
|
I also tried this fix...
Since I could not get hold of a replacement fuse, thought I would just bidge the connection. Wasn't very easy since the solder was not holding to the contacts (maybe the soldering lead was not good enough) and took me a while to manage the bridging... Boy, the fuse is damn small... and I am sure I touched some of the nearby components with the soldering iron...
But nonetheless, I put my phone for charging and it was charging!!! I fully charged the phone... used it for the whole day without any problems... set the alarm for the morning while I went to sleep...
morning I woke up to the faint noise from the phone which sounded like the noise of continuos firing of a small relay! and this started at exactly the time I had set the alarm to.
I checked the phone and RATS!!! the display would not come up. I removed the battery and put it back... and the phone does not turn on again... I haven't looked at tha state of the fuse bridge but I guess my phone is dead for good...
|
|
|
|
|
|
Newbie
Group: Members
Posts: 9
Joined:
Member No.: 7,904
|
How to force charge mpx200 running wm5.0??QUOTE (Toad @ Dec 2 2004, 10:16 AM) If you're having problems charging your phone, before taking apart your phone, I would first suggest you go into engineering mode by dialing * #**364# and pressing the middle blue key, and then going to Options > Layer 1B > Force Charge. Also, I would suggest sending your phone back to Motorola under warranty rather than taking it apart, as that would void your warranty. Is there an equivalent command for mpx200 running wm5.0. This doesn't seem to work with wm5.0. Says 'command not supported' but works with my mpx220 running wm2003se. Anyone please help.
This post has been edited by sofene:
|
|
|
|
|
|
Member
Group: Members
Posts: 33
Joined:
Member No.: 10,244
|
So far I read bad experiences about bridging the fuse. Anyone has good experiences with bridging the fuse?
|
|
|
|
|
|
Member
Group: Members
Posts: 33
Joined:
Member No.: 10,244
|
I have a question about the replacement fuse, does it have to be a slow fuse? or a fast one?
|
|
|
|
|
|
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
| |